VS Factory Rolex Submariner 126610LV “Starbucks” 41mm QC Inspection Report
VS Factory Rolex Submariner 126610LV “Starbucks” 41mm QC Inspection Report
Product Information
* Factory: VS Factory
* Brand: Rolex
* Collection: Submariner Date
* Reference: 126610LV
* Nickname: Starbucks
* Case / Bracelet: Full 904L Steel
* Dial: Black Dial
* Movement: 3235 Automatic Movement
* Crystal: Sapphire Crystal
Technical Specifications
* Measured Case Width: 40.2 mm
* Measured Case Thickness: 12.5 mm
* Measured Weight: 158.8 g*
* Movement: 3235 Automatic Movement
* Beat Rate: 28,800 BPH
* Crystal: Sapphire Crystal
* Material: 904L Steel
*The 158.8 g figure is the actual measured weight of the individual watch inspected. Bracelet sizing, production tolerances and individual assembly may result in small differences between watches.
Timegrapher Test Results
Test Item Measured Result
Daily Rate +4 sec/day
Amplitude 280°
Beat Error 0.1 ms
Beat Rate 28,800 BPH
QC Data Reference
These readings were recorded directly from this individual VS Factory Rolex Submariner 126610LV during its pre-shipment QC inspection.
Mechanical movement readings can vary according to mainspring power, testing position, temperature and other testing conditions. The recorded +4 seconds/day therefore represents the performance observed from this specific watch during testing rather than a permanently fixed daily rate.
For our pre-shipment QC reference, a daily deviation within approximately ±0–15 seconds/day is considered within the normal operating range used for this type of movement inspection.
3235 Automatic Movement Test
This VS Factory Submariner 126610LV uses a 3235 automatic movement operating at 28,800 vibrations per hour.
The individual movement tested recorded:
* Daily Rate: +4 Seconds/Day
* Amplitude: 280°
* Beat Error: 0.1 ms
* Beat Rate: 28,800 BPH
The recorded figures showed stable operation under the test conditions.
Movement QC should not rely solely on the Timegrapher result. Automatic winding, manual winding, crown operation, time setting and date adjustment should also be tested individually before shipment.
Actual Case Measurements
Measurements taken directly from this individual watch:
Measurement QC Result
Case Width 40.2 mm
Case Thickness 12.5 mm
Weight 158.8 g
These figures provide actual QC measurement data from this individual watch, rather than estimated specifications.
Although the 126610LV belongs to the nominal 41 mm Submariner generation, our individual QC sample measured 40.2 mm at the specific case measurement points used during inspection.
This distinction is useful when comparing nominal manufacturer sizing with physical measurements taken from an actual watch.
158.8g Weight and Full-Steel Configuration
The individual watch inspected weighed 158.8 g.
Weight should be considered together with bracelet sizing, case dimensions and the complete configuration rather than used alone as an indicator of quality.
For this QC sample, the combination of the steel case and bracelet produced a substantial overall feel while maintaining the familiar proportions of the modern Submariner design.
Because bracelet sizing and normal production tolerances can affect the result, 158.8 g should be treated as the measured value of this particular watch rather than a fixed specification for every VS 126610LV.
Black Dial Inspection
The black dial provides strong contrast against the applied markers and hands, making alignment relatively easy to inspect closely.
QC should include:
* Dial surface condition
* Printing consistency
* Hour-marker alignment
* Hand alignment
* Date-window positioning
* Date numeral centering
* Luminous application
* Dial cleanliness
The dial should also be inspected under different lighting angles to identify visible surface or alignment issues.
Sapphire Crystal and Cyclops Inspection
This version uses a sapphire crystal.
Pre-shipment inspection should cover:
* Crystal clarity
* Surface condition
* Visible scratches or chips
* Crystal installation
* Cyclops positioning
* Date-window alignment
* Date visibility
* Edge condition
The relationship between the cyclops and date window is particularly important because misalignment can be easily visible from the front.
Bezel Inspection
The green bezel is the defining visual characteristic behind the “Starbucks” nickname.
During QC, the bezel should be checked for:
* Rotation
* Click consistency
* 12 o’clock marker alignment
* Insert positioning
* Scale and numeral condition
* Excessive lateral movement
* Surface condition
The bezel should rotate consistently and align correctly at the reference position.
904L Steel Case and Bracelet Inspection
The case and bracelet are specified here as 904L steel.
QC inspection should include:
* Case brushing
* Polished surfaces
* Surface transitions
* Crown guards
* Crown operation
* Bracelet-link articulation
* End-link fit
* Bracelet-to-case integration
* Clasp operation
* Clasp locking security
These areas should be checked on the individual watch because assembly and finishing can vary slightly between pieces.
QC Data Observations
This individual VS Factory Rolex Submariner 126610LV recorded:
* +4 seconds/day
* 280° amplitude
* 0.1 ms beat error
* 28,800 BPH
* 40.2 mm measured case width
* 12.5 mm measured thickness
* 158.8 g measured weight
The 3235 automatic movement showed stable readings under the recorded testing conditions.
For this model, the most useful QC reference is not a general statement about the factory but the combination of actual movement data, dimensions, weight and individual component inspection.
Particular attention should be given to the bezel alignment and operation, cyclops and date-window positioning, dial and hand alignment, bracelet assembly and clasp operation.
These measurements can also provide useful reference data when comparing future VS production pieces or other factory versions of the 126610LV.
Pre-Shipment QC Inspection
* ✔️ 3235 automatic movement checked
* ✔️ Timegrapher test completed
* ✔️ +4 seconds/day recorded
* ✔️ 280° amplitude recorded
* ✔️ 0.1 ms beat error recorded
* ✔️ 28,800 BPH confirmed
* ✔️ Automatic winding checked
* ✔️ Manual winding checked
* ✔️ Crown operation checked
* ✔️ Time-setting function checked
* ✔️ Date adjustment checked
* ✔️ Case width measured at 40.2 mm
* ✔️ Case thickness measured at 12.5 mm
* ✔️ Individual watch weight measured at 158.8 g
* ✔️ Sapphire crystal inspected
* ✔️ Cyclops alignment checked
* ✔️ Black dial surface inspected
* ✔️ Hour-marker and hand alignment checked
* ✔️ Luminous application visually inspected
* ✔️ Green bezel alignment checked
* ✔️ Bezel rotation checked
* ✔️ Case finishing inspected
* ✔️ Bracelet articulation checked
* ✔️ End-link fit inspected
* ✔️ Clasp locking operation checked
* ✔️ Overall exterior assembly inspected
* ✔️ Final pre-shipment QC inspection completed
QC Status
Inspection Result: PASS
QC Status: Pre-Shipment Quality Inspection Completed
FAQ
What movement does the VS Factory 126610LV use?
The inspected watch uses a 3235 automatic movement operating at 28,800 BPH.
What were the actual Timegrapher results?
This individual watch recorded +4 seconds/day, 280° amplitude and 0.1 ms beat error during testing.
Why did this 41mm model measure 40.2mm?
The 126610LV belongs to the nominal 41 mm generation, while our QC measurement recorded 40.2 mm at the specific case measurement points used during inspection. Nominal model sizing and physical caliper measurements are not always identical.
How thick is the VS Factory 126610LV?
This individual watch measured 12.5 mm in thickness.
How much does it weigh?
The inspected watch measured 158.8 g. Bracelet sizing and individual production tolerances can result in small differences.
What should be checked during QC on the 126610LV?
In addition to the 3235 movement, the bezel operation and alignment, cyclops position, date display, dial and hands, sapphire crystal, bracelet and clasp should all be inspected before shipment.
